pad
homeproductsfeaturesspecial offerssupportcontactshopping basket
pad
cordless phones | headsets | telephones | fax-machines | phone systems | assisted living | novelty phones
Viking Electronics BLK-3-EWP Blue Line Status Strobe Light Kit with EWP For Ring/Loop Detection

pad
Want Phones Price: $157.44
Regular Price: $199.95
You are saving:$42.51
The BLK-3-EWP provides high visibility indication of analog line status through a high powered one million candle power strobe light. The BLK-3- EWP is the ideal solution for the hearing impaired and can be used equally well in loud warehouses or factories, where ringing phones can not be heard. Alternatively, the BLK-3-EWP can be used to add emergency notification to pre-existing emergency phones by turning on the strobe light when the emergency phone is in use.

The included LDB-3 control module has a disable input which is ideal for two-button emergency phones, such as Viking’s E-1600-20A, allowing "Info" button calls to be placed without activating the relay (turning on the emergency strobe light, camera, etc.) Three DIP switches are provided for turning ring detection on or off, off-hook/loop detection on or off and for selecting a ring cadence mode which allows the relay to follow ringing or to remain activated during the off time of standard ring cadence.

The control module can be installed on any standard telephone line or analog PABX/KSU station. The 1 million candle power strobe can be interfaced to flash on ringing, off-hook or a combination of ringing and off-hook (line in-use). The LDB-3 ring/loop detect control module is also available separately.

The kit includes: (1) LDB-3 control module, (1) blue strobe light, (1) 12V DC power adapter, (13) gel filled butt connectors and (1) single gang weatherproof mounting box with gaskets and hardware.

EWP products feature weather-sealed trim pots and DIP switches, a special rubber microphone boot and a mylar speaker with a rubber gasket acting as a primary shield against water penetration. If required, face plate gaskets are provided to further eliminate water infiltration. All connections are hand soldered to eliminate corrosion, and the connections at the push button switch, microphone, and "Call Connected" LED are also hand sealed using a special non-corrosive electronics grade flexible silicone sealant. The entire circuit board is "potted" in a flexible urethane encapsulating material, leaving the weather sealed field-adjustable trim pots and DIP switches accessible for on-site programming. The flexible urethane sealant allows the circuit board and its components to expand and contract, while maintaining weather resistance. To protect the tip and ring connections, special connectors filled with anti-corrosive sealing gel are included

Applications
  • Ringing Phone or TTY indication for the hearing impaired
  • Ringing phone indication in loud warehouses and factories
  • Emergency illumination for emergency phones in elevators, campuses, hallways, parking ramps, etc.
  • Alarm indication for security systems or alarm panels with phone dialers

    Features
  • LDB-3 control module with Enhanced Weather
  • Protection (EWP) included
  • Polycarbonate lens
  • Strobe and control module may be installed separately
  • Long life 1 million candle power blue strobe light
  • Flush mount or surface mount with weatherproof single gang box (included)
  • 3/4" knockouts for connecting conduit, etc.
  • Can be configured to signal ringing off-hook or a combination of both ringing and off-hook (line in-use)
  • One set of (NO) normally open and (NC) normally closed relay contacts provided
  • Selectable ring cadence mode (strobe light will remain flashing between rings)
  • Switched 12V DC output (follows relay activation for powering strobe lights, cameras, etc.)
  • On/off switches for ring detection and off-hook/loop detection
  • Disable input, ideal for use with two-button emergency phones (E-1600-20A), will not activate strobe light on "Info" calls
  • One year warranty
  • Made in the USA

    Specifications
  • Power: 120V AC to 12V DC adapter provided
  • Strobe Dimensions: 111mm diameter x 69mm (4.38" x 2.75")
  • Control Module Dimensions: 74mm x 53mm x 25mm (2.9" x 2.1" x 1.0")
  • Operating Temperature: -26° to 54°C (-15° to 130° F)
  • Relay Contact Rating: .5A @ 125V AC/1A @ 30V DC
  • Minimum Loop Current: 15 mA
  • Minimum Ring Voltage: 25V RMS
  • Strobe Output: 1 million candle power @ 1 second flash rate
  • Ringer Equivalence: 0.5 A REN
  • Disable/Info Switch Input: 50mA/80mW maximum
  • Mounting: Fasten to wall, post, etc. with complete surface mounting hardware included
  • Connections: Color coded wires with gel-filled butt connectors
  • pad
    Want Phones Price: $157.44
    Regular Price: $199.95
    You are saving:$42.51
    Availability: Usually ships the same business day.
    pad
    padpad
    Item Code: 5831
    Customer service lines at Want Phones are open from 7am - 5pm PST -- Monday thru Friday
    Call us at 425-608-5290 to speak to a representative or email us at [email protected]
    © copyright 1999 - 2004 Want Phones -- all rights reserved
    home | support | contact | shopping basket
    ©copyright 2002 wantphones - all rights reserved